-10% Terminator X MPFI Kit for Ford Modular 4.6 & 5.4 Engines

What's Terminator X?

Holley's Terminator X family of EFI Systems are standalone engine management systems that closely replicate some of Holley's most advanced engine management systems but at a much more budget-friendly price. This PDF gives a highly detailed comparison of the Terminator X and X Max to engines built using the Holley HP and Dominator ECUs. To summarize, Holley was able to leave out some features found to be less-necessary by the majority of users and, in doing do, slash the price of a full-featured EFI System by half.  If you're switching your carbureted engine to multi-point EFI or are swapping a fuel-injected engine into your ride and need to stay on a budget, this is the EFI system for you.

Here are some of the features that are included in each Terminator X kit:

Different Terminator X EFI Systems For Different Applications

Yes, there are quite a few different Terminator X EFI System--nearly 100 with more on the way.  All Terminator X systems include the Terminator X ECU. This ECU includes an on-board 1-BAR MAP sensor or you can add an external MAP sensor for boosted applications. On-Board Diagnostic LEDs display the status of ECU Power, Engine Run, Wideband Status, TPS Calibration, Crank Signal, and Cam Signal

In addition to the ECU the kit all Terminator X / X-Max systems include the following:

  • ECU Power Harness
  • Application-Specific Main Harness
  • 3.5-inch Touchscreen LCD Display with Setup Wizard app
  • Custom 4-input / 4-output harness pre-configured for two Electric Fans, A/C Kick, and A/C Shutdown
  • Bosch LSU 4.9 Wideband O2 Sensor

Unique To The Terminator X MPFI Kit for Ford Modular 4.6 & 5.4 Engines

Holley provides many features unique to the Ford Modular 4.6 & 5.4 Engine that make this EFI system a breeze to install and configure and powerful to operate.

  • Direct-fit connectors for factory sensors
  • Ignition harness for factory ignition coils*
  • Two Four-Channel Coil Driver Modules for Ford Ignition Coils*
  • Plug-And-Play connectors for Holley's Smart Coil Kit**
  • Coyote T-VCT controller and harness
  • Choose from EV1 or EV6 injector harness
  • *Except Smart Coil Version
  • **Smart Coil Version Only

Choose From Six Different Versions of the Terminator X MPFI Kit for Ford Modular 4.6 & 5.4 Engines

Part NumberManuf.EngineECUInjector
Harness
Transmission
Control
Drive-By-Wire
Control
550-1216Ford2V Engine with Stock Coils
XEV1NoNo
550-1217Ford2V Engine with Stock Coils
XEV6NoNo
550-1218Ford4V Engine with Stock Coils
XEV1NoNo
550-1219Ford4V Engine with Stock Coils
XEV6NoNo
550-1220Ford2V & 4V Engine with Holley Smart Coil Kit
XEV1NoNo
550-1221Ford2V & 4V Engine with Holley Smart Coil Kit
XEV6NoNo

What Else Will I Need?

Required:  EFI Fuel System with

  • EFI Fuel Pump (Many great options here)
  • Pre- and Post-Pump Filters
  • Fuel Pressure Regulator
  • Associated Hose, Hose Ends, Clamps, Adapters, Etc.

The Smart Coil capable systems above only make provision for the Holley Smart Coil Kit. The kit itself must be purchased separately.

Recommended:

Not Sure? Review this product documentation before you buy!

 
Quickstart Manual
Holley Terminator X and X Max EFI Systems

 
Tuning Manual
Holley Terminator X and X Max EFI Systems

ECU
Boost ControlYes (Requires Additional Hardware)
DIS OutputsEight
FamilyTerminator X
Fueling StrategySpeed Density, Alpha-N, or Combination
Includes Power HarnessYes
Injector DriversEight High Impedance
Internal DataloggingNo. All datalogging done via external device (handheld, laptop, digital display.)
Nitrous ControlYes (Requires Additional Hardware)
Number of CylindersEight
User Configurable I/OYes
User-Selectable MAP StorageNo
Water-Methanol ControlNo
Displays And Controllers
Auto BrightnessNo
CAN Bus CapableYes (Specific to Holley ECUs Only)
Case/Bezel FinishBlack
ConfigurableMonitor dozens of pre-configured metrics provided by the ECU, including sensors, air/fuel ratio, switched outputs, drive-by-wire data, and more.
Data LoggingYes
Display TypeLCD
FunctionsSetup, Monitor, Tuning
Gauge/Display Size3.5 Inch Rectangular
Internal StorageYes (SD Card)
TouchscreenYes
Harnesses
Harness TypePower Harness, Main Harness, Injector Sub-Harness, I/O Harness, Ignition Adapter. Transmission Harness (Transmission Control Versions Only), DBW Harness (DBW Versions Only)
TerminatedYes
Crank Timing
Sensor Harness IncludedDirect-Fit Connector to Factory Crank Timing Pickup
Sensors
TypeECU-mounted 1 BAR MAP, Wideband O2
General
Also IncludedI/O Harness
ApplicationFord Modular 4.6 & 5.4 Engine
Emission Code3 - This part is legal for sale and use on Uncontrolled (Non-Emissions Controlled) Vehicles and Racing Use Only Vehicles.
Unit of SaleKit

Write a review

Note: HTML is not translated!
    Bad           Good

Terminator X MPFI Kit for Ford Modular 4.6 & 5.4 Engines

  • Views: 18651
  • Brand: Holley EFI
  • Product Code: 550-1216 | 550-1217 | 550-1218 ...
  • Availability: In Stock
  • $2,033.00
  • $1,828.95

Available Options

Loading...