-11% Terminator X MPFI Kit for GM LS1 & LS6 Engines

What's Terminator X?

Holley's Terminator X family of EFI Systems are standalone engine management systems that closely replicate some of Holley's most advanced engine management systems but at a much more budget-friendly price. This PDF gives a highly detailed comparison of the Terminator X and X Max to engines built using the Holley HP and Dominator ECUs. To summarize, Holley was able to leave out some features found to be less-necessary by the majority of users and, in doing do, slash the price of a full-featured EFI System by half.  If you're switching your carbureted engine to multi-point EFI or are swapping a fuel-injected engine into your ride and need to stay on a budget, this is the EFI system for you.

Here are some of the features that are included in each Terminator X kit:

  • *Except "Tuner" versions
  • **Requires hardware not included with Terminator X system to implement
  • ***X Max Version Only

Different Terminator X EFI Systems For Different Applications

Yes, there are quite a few different Terminator X EFI System--nearly 100 with more on the way.  All Terminator X systems include either a Terminator X or Terminator X Max ECU. The Terminator X Max ECU provides connectivity for transmission control and drive-by-wire harnesses and is included only in those kits that require one or both of these features. Both ECUs include an on-board 1-BAR MAP sensor or you can add an external MAP sensor for boosted applications. On-Board Diagnostic LEDs display the status of ECU Power, Engine Run, Wideband Status, TPS Calibration, Crank Signal, and Cam Signal

In addition to the ECU the kit all Terminator X / X-Max systems include the following:

  • ECU Power Harness
  • Application-Specific Main Harness
  • 3.5-inch Touchscreen LCD Display with Setup Wizard app*
  • Custom 4-input / 4-output harness pre-configured for two Electric Fans, A/C Kick, and A/C Shutdown
  • Bosch LSU 4.9 Wideband O2 Sensor
  • *Except "Tuner" versions

Unique To The Terminator X MPFI Kit for GM LS1 & LS6 Engines

Holley provides many features unique to the GM LS1 & LS6 Engine that make this EFI system a breeze to install and configure and powerful to operate.

  • Direct-fit connectors for factory sensors
  • Connector for factory ignition coil sub-harness
  • Transmission harness for GM 4L60E, 4L65E, early 4L70E, 4L80E, and 4L85E transmissions*
  • Drive-By-Wire harness for GM LS DBW throttle body*
  • Choose from EV1 or EV6 injector harness
  • *Transmission Control Versions Only
  • *Drive-By-Wire Control Versions Only

Choose From Eight Different Versions of the Terminator X MPFI Kit for GM LS1 & LS6 Engines

Part NumberManuf.EngineECUInjector
Harness
Transmission
Control
Drive-By-Wire
Control
550-903GMLS1 & LS6 EngineXEV1NoNo
550-909GMLS1 & LS6 EngineXEV6NoNo
550-929GMLS1 & LS6 EngineX MaxEV1NoYes
550-932GMLS1 & LS6 EngineX MaxEV6NoYes
550-916GMLS1 & LS6 EngineX MaxEV1YesNo
550-919GMLS1 & LS6 EngineX MaxEV6YesNo
550-926GMLS1 & LS6 EngineX MaxEV1YesYes
550-934GMLS1 & LS6 EngineX MaxEV6YesYes

What is the "Tuner" Version?

When the Terminator X system is installed by a professional tuner they use the Terminator X Software to create a tune and do not require the setup wizard on the handheld display to build the initial configuration. The end user might then choose to upgrade to a higher level of dash or digital display and have no use for the handheld display that is included in the standard version. By opting for the Tuner Version, the 3.5-inch Handheld Touchscreen LCD Display is replaced with a CAN-to-USB harness.  The difference in price can be either pocketed or used toward the purchase of the larger display.

What Else Will I Need?

Required:  EFI Fuel System with

  • EFI Fuel Pump (Many great options here)
  • Pre- and Post-Pump Filters
  • Fuel Pressure Regulator
  • Associated Hose, Hose Ends, Clamps, Adapters, Etc.

Recommended:

  • *Included in "Tuner" versions

Not Sure? Review this product documentation before you buy!

 
Quickstart Manual
Holley Terminator X and X Max EFI Systems

 
Tuning Manual
Holley Terminator X and X Max EFI Systems

 
Installation Manual
Holley Terminator X and X Max EFI Systems for GM LS & Truck Engines

 
Wiring Diagram
Holley Wiring Harness for GM LS1, LS6, and 97-07 Truck Engine

ECU
Boost ControlYes (Requires Additional Hardware)
DIS OutputsEight
FamilyTerminator X
Fueling StrategySpeed Density, Alpha-N, or Combination
Includes Power HarnessYes
Injector DriversEight High Impedance
Internal DataloggingNo. All datalogging done via external device (handheld, laptop, digital display.)
Nitrous ControlYes (Requires Additional Hardware)
Number of CylindersEight
User Configurable I/OYes
User-Selectable MAP StorageNo
Water-Methanol ControlNo
Displays And Controllers
Auto BrightnessNo
CAN Bus CapableYes (Specific to Holley ECUs Only) (Except Tuner Versions)
Case/Bezel FinishBlack (Except Tuner Versions)
ConfigurableMonitor dozens of pre-configured metrics provided by the ECU, including sensors, air/fuel ratio, switched outputs, drive-by-wire data, and more. (Except Tuner Versions)
Data LoggingYes (Except Tuner Versions)
Display TypeLCD (Except Tuner Versions)
FunctionsSetup, Monitor, Tuning (Except Tuner Versions)
Gauge/Display Size3.5 Inch Rectangular (Except Tuner Versions)
Internal StorageYes (SD Card) (Except Tuner Versions)
TouchscreenYes (Except Tuner Versions)
Harnesses
Harness TypePower Harness, Main Harness, Injector Sub-Harness, I/O Harness, Ignition Adapter. Transmission Harness (Transmission Control Versions Only), DBW Harness (DBW Versions Only)
TerminatedYes
Crank Timing
Sensor Harness IncludedDirect-Fit Connector to Factory Crank Timing Pickup
Sensors
TypeECU-mounted 1 BAR MAP, Wideband O2
General
Also IncludedI/O Harness
ApplicationGM LS1 & LS6 Engine
Emission Code3 - This part is legal for sale and use on Uncontrolled (Non-Emissions Controlled) Vehicles and Racing Use Only Vehicles.
Unit of SaleKit

Write a review

Note: HTML is not translated!
    Bad           Good

Terminator X MPFI Kit for GM LS1 & LS6 Engines

  • Views: 29314
  • Brand: Holley EFI
  • Product Code: 550-903 | 550-909 | 550-916 | 550-919 ...
  • Availability: In Stock
  • $1,606.95
  • $1,427.95

Available Options

Loading...